These are error codes for Whirlpool Washing Machines. We hope these fault codes will help you get to the bottom of your problem. If you require any help why not leave a comment or post a question on our forum.
whirlpool

Washing Machine
Fault Code Fault
FH No Water Inlet
FA Aquastop Failure
FP Drain Failure
F5 NTC Failure
F6 Tachometer Failure (no motor movement detected)
F7 Triac Short Circuit detection
F8 Heating Element, Open Circuit
F9 Overflow Failure
F10 Motor control unit (Thermal)
F11 Communication failure
F12 Heating Element Short Circuit
F13 Dispenser Circuit Error
F14 EEPROM Failure
F15 Motor Control Unit Error
F16 Control Failure (Control Unit)
F18 Control Failure (Control Unit)
F20 Control Failure (Control Unit)
F21 Control Failure (User Board)
F22 Control Failure (User Board)
FDL Door Lock Error
FDU Door Unlock Error

Here are some Whirlpool model numbers these codes might apply to:

AQUA9759, AQUA9760, AQUA9769B, AQUA9770, AQUA9770B, AQUASTEAM976, AWOD4505, AWOD4605, AWOD5526, AWOD5527, AWOD5706S, AWOD5726, AWOD5727, AWOD5926, AWOD6527, AWOD6528, AWOD6727, AWOD6728, AWOD6927, AWOD6927S, AWOD6928, AWOE8548, AWOE8558, AWOE8559, AWOE8748, AWOE8758, AWOE8759B, AWOE8760, AWOE8760B, AWOE9558, AWOE9558B, AWOE9558S, AWOE9559B, AWOE9559S, AWOE9759, AWOE9760, HDW1010SI, HDW1011WG, PROW0612IIM, PROW0614I, SCW1112WH, ACM880, ACM883, AMH244, AQUA9769, AWM023, AWM1000, AWM3203, AWM3213, AWM3233WH, AWM3243, AWM3253, AWM3283, AWM3363, AWM3373, AWM5104, AWM51043, AWM51044, AWM51045, AWM5125, AWM51254, AWM51255, AWM5125S, AWM5145, AWM51452, AWM51453, AWM51454, AWM51455, AWM51455SP, AWM6100, AWM61001, AWM6120, AWM61201, AWM61203, AWM6123, AWM6140, AWM61403, AWM6141, AWM61411, AWM8000, AWM8101, AWM8103, AWM81031, AWM81131, AWM8121, AWM8123, AWM81231, AWM81233, AWM8125, AWM81253, AWM8143, AWM81431, AWM81433, AWM8145, AWM81453, AWM8163, AWM81631, AWM81633, AWM9000, AWM9100, AWO10561, AWO10761, AWO10961, AWO12963, AWO129635, AWO12963S, AWO3561, AWO35615, AWO3571, AWO3761, AWO37615, AWO37615S, AWO3761S, AWO3771, AWO3961, AWO39615, AWO5763, AWO57635, AWO5963, AWO59635, AWOD4305, AWOD4705, AWOD5306, AWOD5316, AWOD5506, AWOD5516, AWOD5556, AWOD5706, AWOD5716, AWOD6507, AWOD6707, AWOD7508, AWOD7708, AWOD8508, AWOD8708, AWODAS128, AWODAS148, AWT51084, AWT51085, HDW0614WG, HDW1011BG, SCW1012UG, WAWM51045,

These are accurate to the best of our knowledge | wm1.com

Share

83 Responses to “Whirlpool Washing Machine Fault Codes”

  1. fausto says:

    machine will not do any thing shows code 06 .

    [Reply]

    Washing Machine Man Reply:

    do you have the model number of your machine ?

    [Reply]

    Edwina Reply:

    We have a code F13? Please advise, thanks

    [Reply]

    Edwina Reply:

    Model AWEO8759

    [Reply]

  2. jacques simard says:

    my model is whirlpool wfc7500vw

    thank you

    [Reply]

  3. Chris says:

    My model is a AWOD AS147 and the fault code is F07 – “Triac short circuit detection” according to the above, but I’m not sure that’s what the issue is.
    The motor and the pump are going, but the drum isn’t turning. When I turn the drum by hand it makes a disagreeable noise, like something has broken within the mechanism that controls the drum spin.

    [Reply]

    Washing Machine Man Reply:

    Check the carbon brushes and the commutator plates on the armature this could be making the noise and the circuit fault.

    Let me know how you get on…

    [Reply]

  4. Chris says:

    Had a repairer out, it’s the bearings which have gone. Thanks anyway!

    [Reply]

  5. chris says:

    hello

    My model is a AWO10761 the fault code is F6 or F15,the motor makes noise, no power to turn the drum
    many thanks

    [Reply]

    Washing Machine Man Reply:

    The first thing I’d check is the carbon brushes and the armature on the motor to make sure everything is fine there.

    Have a look and let me know how you get on.

    [Reply]

  6. dawn says:

    we have whirlpool 6 sense washing machine error coming up is f13
    please advise
    thank you

    [Reply]

    mattnall Reply:

    I have the same code, F13, on a whirlpool AWO D5716. When I turned the control dial to OFF and then back on again the power wouldn’t come on – no lights etc. and door wouldn’t open.

    After a couple of minutes the door unlocked and now the power is back on and everything seems fine. Ran a ‘rinse and spin’ cycle and it stopped with the same code.

    Now when the door releases power doesn’t come back on.

    Any help appreciated.

    [Reply]

  7. Eoin Forrestal says:

    I have a whirlpool AWOD 4505. The service light has come on. Is it possible to repair myself?

    [Reply]

  8. Nicola says:

    I have AWM 6140/3 the washing machine starts up fine until it starts to fill with water then just cuts out.I have had the brushes replaced as someone suggested this may be the problem but it still isnt working.Any ideas????

    [Reply]

  9. MARIA says:

    MY MODEL IS WTW6600SWI THE FAULT CODE IS LD DOOR DON’T UNLOCK

    [Reply]

  10. may says:

    I have AWO/D5716 3 YEARS OLD Fo8 keeps appearing, have been told its the heating element on open ciruit as above, engineer has been out and looked at everything but it is not that is it the relay? or something else

    [Reply]

  11. PAUL says:

    WE HAVE A WHIRLPOOL 6th SENCE AWOE9558S 8 MONTHS OLD IT KEEPS COMING UP WITH F13 HAD WHIRLPOOL OUT AND THEY REPLACED DOOR LOCK AND CATCH BUT IT STILL DOES F13 WHEN ITS AT THE END OF WASH WHEN ITS READY TO DO ITS LAST SPIN

    [Reply]

  12. William says:

    Our Whirpool Duet Sport ( Washing Machine) came up with error code SD at the end of the whole washing cycle! Is it any thing to worry about??

    [Reply]

  13. annemarie says:

    my washer is showing fault f11, please help. my washer is a wirlpool awo 3761/5

    [Reply]

  14. Paul says:

    Hi,
    I have a AWO3561 that has stopped working. A fault code has come up and I think it was F11 but the code doesn’t come up anymore. Is there a way to bring up the fault code again?

    [Reply]

  15. neil says:

    fault code fp drain failure what could cause this , machine starts does half a cycle then stops I then move the machine but it onto spin and it works

    [Reply]

  16. Bruce says:

    Hi

    I have a Whirlpool AWM 8163-gb 857081615000.

    Shows no error codes, but door light is on. Switch replaced but light still on.

    Any advice appreciated.

    [Reply]

  17. Stewart says:

    Hi,
    I have an AWM 1000 which comes up with an F10 code constantly and will not move from one cycle to the next. Any suggestions most welcome. Apparently this code is the ‘Motor Control Unit (Thermal)’. What does that mean?

    Many thanks for any help.

    [Reply]

  18. Mrs. Cooper says:

    We have the fabric sense system, whirlpool washing machine and just all of a sudden it stopped spinning. It makes the sound and goes through the whole cycle, the water drains completely but after that it will not spin but it goes to the end of the cycle and cuts off. My clothes are completely and with the spin process they are almost dry. Should I look into a repair or is the machine just done. We have had it for 3 & 1/2 years. Thanks, Mrs. Cooper 6/4/2011

    [Reply]

  19. al says:

    F A flashes how do i fix it please

    [Reply]

  20. Alex says:

    We have a whirlpool 6 sence colour mod WWDC8429/1 the fabric conditioner goes down far too early well before the final rinse. Can you tell me why. Alex

    [Reply]

  21. Omer says:

    My Machine model is AWZ5210E
    The bell sign appear on the screen
    & can’t open the door ??

    [Reply]

  22. Nikki says:

    Have whirlpool7.5 6th sense comes up with code 23 someone please help

    [Reply]

  23. john says:

    hi
    i have a AWOE8759B, was working fine then made a popping sound and lost all power, checked fuses all ok but washer still dead. can you please help.

    [Reply]

  24. […] Whirlpool Washing Machine Fault Codes | wm1.com – These are error codes for Whirlpool Washing Machines. We hope these fault codes will help you get to the bottom of your problem. If you require any help why not… […]

  25. benny jørgensen says:

    Hej.
    Jeg har en whirlpool AWO/D 6001 vaskemaskine.
    Den viser fejlkode F12.
    Hvad kan det være der er galt.

    [Reply]

  26. Luis says:

    I have a whirlpool wfs1276aw which suddenly stopped displaying error F06.
    I’ve already unplugged it, opened the top, checked and cleaned all electrical connectors. let it rest for a while, tested it but the error continues.
    Any suggestions what should I do to fix it myself?

    [Reply]

  27. Christine says:

    My whirlpool 6th sense WFE 1485BD with a fault code F:12

    [Reply]

  28. mary treglown says:

    I have a whirlpool model number WSF1273BD is is showing error F07.

    can you advise what is require to fix it

    [Reply]

  29. Andy says:

    i have a whirlpool awm900 and it keeps beebing f5 after 2mins of wash cycle and now and again it comes up f11 wot does ntc mean please thankyou

    [Reply]

  30. My washing machine is showing ESC. What does that mean ?

    [Reply]

  31. rupert says:

    f12 code keeps showing also makes a lot of noise when spinning(very loud) model awo/d5716

    [Reply]

  32. moudi says:

    I have a AWD8810 please help f8 and f23

    [Reply]

  33. Tml01 says:

    My machine is an AWO/D 5556 with an F-07 fault code. I looked it up and it says Triac Short Circuit. Where is this component a is it DIY REPLACEABLE?

    [Reply]

  34. Linda says:

    What i can do how fix this if my washmashine show problem service f12???please answer

    [Reply]

  35. Viviane says:

    My washing machine SM8280928 Catalyst shows errir 06, what does it mean?

    [Reply]

  36. nemad says:

    I have AWE 9725 and in display is faul code F14 – what can I do.?
    Than you very much to your hepl.
    N

    [Reply]

  37. hadi says:

    fa error
    what is this????

    [Reply]

  38. Rory says:

    Whirlpool zen (6th sense) AWE 9765 GG

    I have error code F-22. What is this and how can it be repaired?

    [Reply]

  39. Ste says:

    Have an F06 and my washer starts to spin then stops

    [Reply]

  40. Val says:

    My whirlpool AWOD55256 washing machine is 5 years old and stopped working fault F06 comes up and says services. What’s wrong with it and is it worth fixing. Thanks for your help

    [Reply]

  41. Daniel Blood says:

    Hi…..I have whirlpool awo/d 61000 front loader ……n power on displa…..tested to pcb……..mains fine……..can anybody help……….machine was operating and just went dead.

    [Reply]

  42. Pom says:

    We have an fo8 error code on our Whirlpool 6th sense WFE1485BD, we understand that this is an heating element error.
    Question is how do we clear it?
    Still have the door locked and clothes inside, with water.
    Please could you advise if this is fixable without a technician.

    [Reply]

  43. V.C.Koshy says:

    Hai, My Machine WHIRLPOOL 6th Sense, Model AWOE- SM11314, beginning stage machine working properly but F26 error program stop.
    what is Error F26

    [Reply]

  44. harga emas says:

    I blog often and I genuinely appreciate your content.
    This article has truly peaked my interest. I will bookmark
    your site and keep checking for new information about once per week.
    I subscribed to your RSS feed too.

    [Reply]

Leave a Reply